1/8/2024 0 Comments Sound tools wallcatPair with an additional CAT Rack, CAT Snake, or WallCAT to send and receive four lines of balanced audio. Now you can run up to four lines of audio down a shielded CAT5 cable. Attach your XLR cable ends to channels by selecting either input or output across four channels. Secure the WallCAT inside a compatible electrical junction box and install into the desired position. Combine with our CAT Box, CAT Rack, and/or CAT Tails for the ultimate audio-over-Cat5 experience.Īttach your shielded CAT5 cables in the input or parallel RJ45s at the back of the WallCAT8. Using several SoundTools WallCATs and our SuperCAT cable in your building installation will allow you to run four channels of clear audio and COM signals from one room to another or to multiple rooms at once. Sound Tools WallCAT Audio Over CAT5 Wall Mount - XLR Female WC121-B - Stage Boxes: Send up to four balanced audio lines from one room to another using shielded CAT5/6/7 cable. ![]() They are compatible with 48-volt phantom power. SoundTools Wall CATs require shielded (STP/FTP) Cat cable to function properly. Our high-quality brushed aluminum and stainless steel mounting screws (included) are resistant to rust and most wear-and-tear. Because of our commitment to consistent, high-quality audio and COM signals, WallCATs are designed to keep strong, stable connections. Every connection you need, including 4 Neutrik XLR connectors in front and 2 Amphenol RJ45 connections in back, come pre-installed and clearly labeled. Unlike other brands, our wall plates require no soldering to install. Compatible with analog, DMX, AES3 and intercom signals. With the SoundTools Wall CAT, we set out to create a superior XLR wall plate for sending and receiving audio and COM through shielded CAT cables. SoundTools is committed to the design and manufacture of professional grade audio equipment, whether it's used on a festival stage, in a concert hall, or in your office building. These durable aluminum wall units fit standard 4" electrical junction boxes to provide easy conversion to and from Cat5 cable to four channels of XLR, DMX or COM lines. Send audio and data from one room to another using installed shielded Cat5 cable and SoundTools Wall CATs. That enables audio to be sent from one room to multiple locations or from multiple locations to a single room. Each WallCAT has an input and parallel RJ45. Would heatshrink over the Cat twisted pairs be good enough for a sub snake that will likely remain patched into the main snake? It should only come out to plug a band's splitter in or re-arrange the input order, so likely not very often.The SoundTools WallCAT is designed to transport audio easily and conveniently from one room to the next utilizing shielded CAT5/6/7 cable. What is the best way to make a fan out from Cat5/6 cable?īut our budget is nearly non-existant, which is the reason I'm using Cat cable instead of actual multipair snake cable anyways, so $120 x 5 stage boxes is too much. So despite them sharing the ground connection, the other channels in the box will not get voltage when phantom is sent to just one. No! because +48 is sent over pins 2 and 3, pin 1 only provides the ground. Īre there any consequences to this approach? Looking at the PCB traces on this panel it appears so. Is this how RAT does it in their (expensive) superCAT cables, boxes, and tails? Share the drain wire to all the XLR connectors' pin 1? I'll be plugging in condensers and active DI's so I will need this. ![]() Well yeah, it will work, but what about phantom power? Without pin 1, no +48. Leave all the grounds disconnected and call it good? How can I get 4 channels of balanced and shielded audio over 9 wires? I will be sure that the cable we order is shielded and has the extra drain wire. ![]() Because we are wiring the whole building for low voltage, I will have bulk Cat6 or Cat6a cable available and would like to run the stage boxes with those, probably hard-wired to the XLRs in the stage box, and made to fan out on the other end to the main snake. Each box has either 4 XLRs or 3 XLRs and 1 NL4. I've got some pop-up stage boxes from Parts Express to install in a stage for a new venue.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |